Pro is $50 until November 28, then $100.Get Pro

A Stitchist guide

Trims, jump stitches and tie stitches in an embroidery design

A trim cuts the thread between two parts of a design, a jump moves the hoop without sewing, and a tie stitch locks the thread where it starts and where it ends. Stitchist ties the thread only at those two places, sews a hop shorter than 2 mm as one connecting stitch instead of cutting it, and carries the thread from one stroke of a satin shape to the next underneath the satin. The 2 mm limit is a setting in the export dialog.

Start digitizing free

Free drawing tools and PES / DST export. One free Auto Digitize creation.

From idea to embroidery

Draw · Digitize · Sew

A little preparation makes a better stitch file.

What each one is

A trim is the machine cutting the thread. Before it the thread is tied off, after it the hoop moves and the thread is tied in again. Each trim costs a few seconds, leaves two thread tails on the back, and is one more chance for the needle to come unthreaded. A design with many trims sews slowly and the back gets rough.

A jump is the hoop moving with no stitch. If the thread is not cut first, it is dragged across the fabric and has to be snipped by hand afterwards.

A connecting stitch is an ordinary stitch that happens to cross a small gap. Over a millimetre or two it disappears into the embroidery around it, and it is what joins the strokes of small lettering in professionally digitized designs.

A tie stitch, or lock stitch, is one of a few small stitches sewn up a stitch line and back down it, so the thread end cannot pull out.

How Stitchist decides where to cut

The thread is tied in where it starts and tied off where it is cut or changed, and nowhere else. Two runs that meet end to end are sewn straight through.

A satin shape drawn as an outline is sewn stroke by stroke in one unbroken run. The needle travels from one stroke to the next along a run that the satin sewn afterwards covers, so a letter such as A, K or R needs no trim inside it.

Between two shapes in the same thread, a hop no longer than the limit is sewn as one connecting stitch. A longer hop is tied off, trimmed and tied in again.

A connecting stitch is never laid across another colour that is already sewn, where it would show. There the thread is cut, however short the hop.

A colour change always ends the thread.

The settings that change it

Trim jumps over, in the export dialog, is the limit described above. It starts at 2 mm, about the shortest tail a machine can hold. Set it to 0 to trim at every hop. Raise it if you would rather snip a few longer threads by hand than wait for the machine to cut them.

Tie stitch, next to it, is how long each tie stitch is. It starts at 0.7 mm, and the thread is tied with two of them up the first stitch and the same two back, or one each way where that stitch is too short for two. On a thick or stiff material, such as heavy felt on a firm stabiliser, or leather, set it to 1 mm. The needle then stays clear of the hole it has just made, which is where the thread breaks on such a material. Auto Digitize sets 1 mm by itself when you choose Felt or Leather as the fabric.

Tie-in, Tie-off and Trim after object are switches on each object, under its stitch settings. Turn Trim after object off when the next object starts where this one ends and you want the thread carried over.

Max stitch, also in the export dialog, is the longest single stitch. Longer ones are divided when the file is built.

The order of objects in the Sequence panel decides which hops exist at all. Two objects of one colour that sit next to each other in the design should sit next to each other in the sequence.

Designs you saved earlier

A saved design keeps the stitches of each object exactly as they were saved; opening it does not make them again. Where the thread is tied, cut or carried between those stitches follows the rules on this page whenever the file is built.

An object is made again when you change its shape or one of its stitch settings. From then on a satin outline is sewn stroke by stroke and a fill has no tiny stitches.

What the machine does with the file

File formats record a trim in different ways. DST writes it as a short series of jumps, which the machine reads as a cut. Brother PES and PEC files cut at a jump. A Janome JEF file has no trim of its own, so the machine cuts at jumps according to its own settings.

Many machines also have a setting for the shortest jump they will trim. If your machine leaves a thread where the file has a trim, or cuts where you expected a thread, check that setting in its manual before changing the design.

Common questions

Why is there a thread between two letters?
The gap between them is shorter than the trim limit, so it is sewn as a connecting stitch. Set Trim jumps over to 0 in the export dialog to cut at every hop, or move the letters further apart.
Can a whole letter be sewn without a trim?
Yes. A satin shape drawn as one outline is sewn in one run, with the thread carried under the satin from stroke to stroke. Letters made of separate pieces, such as i and j, have one hop between the pieces.
Does Stitchist remove very short stitches?
Yes. Rows of a fill turn in one needle hole instead of taking a tiny step along the edge, and stitches too short to sew are merged into their neighbours when the file is built.
The thread breaks right where an object starts on thick felt. What can I change?
Set Tie stitch to 1 mm in the export dialog. A stiff material holds the thread fast in the needle hole, so the stitches that tie the thread in need more room between them than they do on soft fabric. A larger needle and a slower start help as well.

Put it into practice

Free drawing tools and PES / DST export. One free Auto Digitize creation.

Start digitizing free →Compare Free and Pro

Still choosing a tool? See free embroidery digitizing software compared.